Go Back   IKEA FANS > Plan and Design > Workspaces
Register Marketplace Blogs Forum/Blog Search Mark Forums Read


Comment
 
LinkBack Thread Tools
No Gallery image is associated with this thread

Old Oct 10th, 08, 2:19 pm   #1
Dezire
IKEA FAN
 
Join Date: Oct 10th, 2008
Posts: 2
iKarma: 50
Gallery: 0
My IKEA: Germany-Stuttgart:Ludwigsburg
Computer workstation Fredrik is shaky, pls help

Hi,

I have the computer work station "Fredrik" ( IKEA | Computer workstations | Desktop solutions | FREDRIK | Computer work station) and I have the following problem: The table is a little shaky, when I try to write something on the desk it gets very annoying. How can I make the table less shaky?

1) By removing the four furniture feet, are they the cause of the shaking?

2) If I install the plate which connects both table legs more downward, will it then get more stable?

Thanks a lot

Dezire is offline  
Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote

Register to remove these ads today!

Old Oct 10th, 08, 5:06 pm  
Moderator; IKEA Chuck
 
Chuck's Avatar
 
Join Date: Mar 1st, 2006
Posts: 2,987
iKarma: 27,882
Gallery: 3
Location: Bala Cynwyd, PA, , USA
My IKEA: USA-Philadelphia:Conshohocken
Doorstyle: The late, great Kvadrat Beech

LBG Adoptions
Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  IKEAFANS Benefactor ($100+ Donation)  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  IKEAFANS Benefactor ($100+ Donation)  IKEAFANS Moderator 
Total Awards: 13

I've been blogged!
Re: Computer workstation Fredrik is shaky, pls help

Welcome to IKEAFANS, Dezire.

Your Frederick desk shouldn't be shaky at all, except that if your floor isn't level, it might rock a bit from one corner to another.

If it really shakes, it's probably not tight enough. Double check your work, and, as you've suggested, make sure the grey metal cross pieces under the desktop are down as tight as they can be.

To make sure of this, use a rubber mallet and give the two pieces a good whack at either end. DON'T use a hammer, as you'll damage those pieces.

If it's a matter of the unit just rocking a bit, try to figure out which is the high end and remove one of the plastic pads from under the legs. Or you can use a some sort of wedge - a shim, folded piece of paper, etc. - to help the leveling process.
__________________
A-P-A-R-T/Together, Inc.
Find out how you can get a piece of Chuck.
Just taking my inner IKEA geek out for a walk.
Come back.
Chuck is offline  
Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old Oct 10th, 08, 6:10 pm  
IKEA FAN
 
Join Date: Oct 10th, 2008
Posts: 2
iKarma: 50
Gallery: 0
My IKEA: Germany-Stuttgart:Ludwigsburg
Re: Computer workstation Fredrik is shaky, pls help

Thanks a lot Chuck!

I have used a mechanic's level and the table seems to be even. I also have a carpeted floor so my question is if I really need those plastic pads under the legs, and if the table would not be more stable if i remove them all because the table will then sit on two lenghty legs and not on four pads.

Will the table become more stable, as you suggested, if I move the cross piece down a little, and if so by how much (like on the IKEA photo?). Currently, the cross piece is right under the table level (3cm under the table level).


Thanks a lot again
Dezire is offline  
Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old Oct 10th, 08, 7:31 pm  
Moderator; IKEA Chuck
 
Chuck's Avatar
 
Join Date: Mar 1st, 2006
Posts: 2,987
iKarma: 27,882
Gallery: 3
Location: Bala Cynwyd, PA, , USA
My IKEA: USA-Philadelphia:Conshohocken
Doorstyle: The late, great Kvadrat Beech

LBG Adoptions
Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  IKEAFANS Benefactor ($100+ Donation)  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  Appreciation of an IKEAFAN  IKEAFANS Benefactor ($100+ Donation)  IKEAFANS Moderator 
Total Awards: 13

I've been blogged!
Re: Computer workstation Fredrik is shaky, pls help

I don't think removing the plastic feet or moving the cross pieces will make much difference. The reason that it seems loose is because of the carpet. Just make sure that the cross piece is firmly in place, wherever you place it.
__________________
A-P-A-R-T/Together, Inc.
Find out how you can get a piece of Chuck.
Just taking my inner IKEA geek out for a walk.
Come back.
Chuck is offline  
Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Comment
Top

Thread Tools


Similar Threads
Thread Thread Starter Category Comments Last Post
FREDRIK Workstation (Computer desk) Instructions Tigratrus IKEA Instructions 1 Sep 21st, 09 8:25 am
How to build up a fredrik workstation? DonkeyFlaps Bedroom and Closet 1 Sep 29th, 08 1:43 pm
Computer Workstation Suggestions briansmith Workspaces 1 Jul 30th, 08 5:59 pm
Unknown Computer Workstation xlgrant Workspaces 2 Jul 17th, 08 1:25 pm
U-Shaped computer workstation with Ikea products ksakamuri Decoration 0 Mar 10th, 08 3:51 pm



Recent Directory Listings

  • A-P-A-R-T / Together
    Chuck Shapiro's been an IKEA Assembler and Installer in the Conshohocken and Philadelphia areas for 20+ years. Will travel!
  • Dyer Studio
    I provide IKEA kitchen design services for the Greater Atlanta Metro area and beyond. If you need assistance with planning your IKEA kitchen, call me today!
  • Kitchen Craft, LLC
    We are the Kitchen Craft LLC Certified Ikea Kitchen Installers in Tampa Bay Area and South, with base in Sarasota FL. We are certified Ikea kitchen installers...
Help an IKEAFAN - Find Threads with Zero Replies
Keep up with IKEAFANS on Twitter and Facebook!